RR7P GE Lighting Controls RR7P Jasco GE RELAY
Amperage Rating | 20 |
Brand | GE Wiring Devices |
Catalog Description | GE Wiring Devices RR7P Standard 3-Wire Low Voltage Relay, 20 AMP, Contact Configuration: SPST, Contact Rating: Lamp Load: 125 VAC 20 AMP Tungsten Filament, 277 VAC 20 AMP Ballast, Resistive Load: 277 VAC 20 AMP, Motor Load: 1/2 HP At 110 - 125 VAC, 1-1/2 HP At 220 - 277 VAC, Mounting: Standard 1/2 IN Knockout, 1 Pole, Connection: 5-Pin Female, Resistance: 75 - 85 OHM At 60 HZ Unrectified, 55 - 60 OHM DC Resistance, Operating Cycles: 50000 Full Load, 100000 No Load, 0 - 60 DEG C Operating Temperature, Environmental Conditions: Relative Humidity: 10 - 95 PCT RH Non-Condensing, Atmosphere: Non-Explosive, Non-Corrosive, Vibration -Stationary Applications NEMA Level A (0.003 IN Amplitude, 1 G Acceleration), Lead Length: 6 IN, UL Listed, CSA Certified |
Connection | 5-Pin Female |
Contact Configuration | SPST |
Contact Rating | Lamp Load: 125 VAC 20 AMP Tungsten Filament, 277 VAC 20 AMP Ballast, Resistive Load: 277 VAC 20 AMP, Motor Load: 1/2 HP At 110 - 125 VAC, 1-1/2 HP At 220 - 277 VAC |
Country Of Origin | USA |
Environmental Conditions | Relative Humidity: 10 - 95 PCT RH Non-Condensing, Atmosphere: Non-Explosive, Non-Corrosive, Vibration -Stationary Applications NEMA Level A (0.003 IN Amplitude, 1 G Acceleration) |
GTIN |
00043180570970 |
Mfr. # | RR7P |
Mounting | Standard 1/2 IN Knockout |
Number Of Poles | 1 |
Operating Cycles | 50000 |
Operating Temperature | 0 - 60 |
Resistance | 75 - 85 OHM At 60 HZ Unrectified, 55 - 60 OHM DC Resistance |
Special Features | Mechanical latching-type units requiring only momentary 24 V rectified AC switch circuit pulses to open or close line-voltage circuits; Employs a split low-voltage coil to move the line voltage contact armature to the ON ( OFF) latched position; The ON coil moves the armature to the right when a 24 VAC control signal is impressed across its leads; This is analogous to a magnet attracting the handle of a standard single pole switch to the ON position when energized; The armature (handle) latches in the ON position and will remain there until the OFF coil is energized, drawing the armature into the OFF position; This control operation provides several key control features: positive action, stable operation, minimal power consumption, additive control functions; May be used to full-rated capacity for tungsten filament, ballast or resistive loads; Do not use this relay to switch DC loads, this will damage the power contacts; Operates in any position; Split coil (1/2 for on, 1/2 for off), compatible with standard interface/drivers, ULN-2003A darlington transistor arrays, operating voltage - nominal: 24 - 29 VAC (plus/minus 10 PCT) rectified, (minimum at relay - 21 VAC rectified), 30 - 38 VDC (plus/minus 10 PCT) filtered, momentary duty rating, minimum activating pulse time: 50 MILSEC, impedance: 75 - 85 OHM at 60 HZ unrectified, 55 - 60 OHM DC resistance, for proper operation, use only half-wave rectified AC voltage for relay control; 0.865 - 0.875 IN (nominal 22 MM) diameter In 14 or 16 AWG material; Two terminals, two back wiring holes per terminal for feed-through wiring, screw-actuated clamps for use with 14 - 10 AWG solid or stranded wire, copper wire only |
Standard | UL Listed, CSA Certified |
Type | Standard 3-Wire Low Voltage Relay |